Firearms Accessories

• Matt black non-glare surface coating to reduce reflections• QD sling attachment point on the rear side of the handguard• M-LOK mounting system to fit all types of M-LOK accessories: rails, vertical grips, AFG, ...• Fits a wide variety of AK 47‘s with stamped and milled receivers with a front sling loop on the gasblock• Lightweight construction made out of high strength 6061 aluminium with MIL-SPEC type III hardcoat anodize finish

RAIL KEYMOD INCLINÉ À 45 DEGRÉS

Claw Gear‘s modular firearms accessories products are designed to increase weapon performance and accuracy. Due to it‘s outstanding materials construction, this rugged and high quality Austrian made item will serve you in any combat situation.NATO STANAG 4694 RailThe nine slot Picatinny rail allows the user to upgrade his AK rifle with various aiming devices or accessories.Adjustment ScrewsAdjust the angle of the mount to align it with the point of bullet impact.Shaped ContourThe design fits to the curve on the receiver cover and even allows to dissable the rifle without dismounting the AK RSM.Emergency SightEven with an optical device mounted the sight can be used as a backup.Compatibility: AK-47, AKM, RPK, AK-74 and all variants with the original Mauser-type adjustable rear sight. Not compatible with SKS rifles.Installation: Dismount the existing rear sight and leaf spring. Put the AK RSM into the guidance on the rear sight base and align both holes. Punch the included roll pin into the bore so it is flush with both sides. Insert the big set screw on top into the middle thread on the rail and tighten it until the emergency sight aims to the point of impact. Finally insert both small set screws into the forward threads and tighten them stoutly. Warning: Torque for setscrew max. 3 NM

Clawgear‘s modular mounting system products are designed to increase weapon performance and handling. Due to it‘s construction in 6082 Aluminum, this rugged and high quality item will serve you in any combat situation.NATO STANAG 4694 RAILThe 13 slot Picatinny Rail allows the user to upgrade his 55X rifle with various aiming devices or accessories.LIGHTWEIGHT CONSTRUCTIONAlthough this mount base has been designed in a lightweight way, its mechanical strength is not being affected.ADJUSTMENT SCREWIt clamps the mount for a solid fit between both attachment points on the receiver and is secured by a clamp screw on the left side.DOVETAIL SLOTThe front attachment point is the dovetail on the receiver which is normally used to fix the brass catcher.AIMING BOREMakes the use of the original diopter sights possible.CompatibilitySIG550, SIG551, SIG552, SIG553, PE90 and all variants of the ri_x001E_ e with standard adjustable diopter sights.InstallationMake sure your weapon is unloaded and safe. Screw the included adjustment screw fully into the mount base. Put the rail on the upper receiver and slide it forward so the dovetail on the receiver connects smoothly to the front of the rail. Then use a 8mm wrench to unscrew the adjustment screw until it moves inside the hole of the rear sight base. Tighten it up for a solid fit. Use the clamp screw on the left side of the mount base to secure its position.

The Clawgear AK Gasetube Cover is an Upgrade part that works in combination with the CG Slimline Handguard.PLEASE NOTE: This Gasetube Cover works ONLY in combination with the Slimline Handguard.Features:• Upgrade part for the Clawgear AK 47 slick handguard• Mil-STD 1913 Picatinny / Stanag 4694 rail on top• Made from high strength aluminium with black milspec hard coating

Clawgear‘s modular firearms accessories products are designed to increase weapon performance and accuracy. Due to it‘s outstanding materials construction, this rugged and high quality Austrian made item will serve you in any combat situation.NATO STANAG 4694 RailThe 4 slot Picatinny rail allows the user to upgrade his Modular Scope Mount equipped AUG rifle with additional accessories.SurfaceHigh alloy aluminium with anodized coating (MIL-8625-F type III, class II) for heavy use.This rails fits the AUG Modular Scope Mount (Art.Nr. 20114)

Clawgear‘s modular mounting system products are designed to increase weapon performance and accuracy. Due to its glass fibre reinforced polymer construction, this rugged and high quality item will serve you in any combat situation. The Modular Scope Mount protects the original optics of AUG rifles and provides mounting possibilites for various Picatinny based accessories.NATO STANAG 4694 RailThe integrated 16 slot Picatinny Rail allows the user to upgrade his AUG rifle with various aiming devices or accessories.Lightweight ConstructionAlthough this mount base has been designed in a lightweight way, its mechanical strength is enhanced by the use of glass fiber reinforced polymer.Mounting PossibilitesAdditional side rails (sold seperately) can be attached to both sides of the AUG MSM to provide additional mounting spots for further equipment.Reduced Infrared SignatureThis accessory part features reduced infrared singature.Flip-Up CoversTwo flip-up covers (included) protect the lenses of the scope from rain, dust, debris and mud.InstallationMake sure your weapon is unloaded and safe. Take the left half-shell (the one without top rail) and place it on the scope by pushing it over the diagonal fixing screw of the scope. Then push the right half-shell into the corresponding slots on the left part until it clicks in. Make sure that all engagement hooks are snapped in. Place each hexagon nut in the clearance of the right shell and tighten the corresponding screw from the left shell side. Mount the included flip-up covers to protect the original scope glass.CompatibilitySteyr AUG A1/A2, AUG P, AUG Z, AUG LMG variants, AUG SA variants, F88 Austeyr. Applies to all variants with 1,5x standard Steyr scope.

Clawgear‘s modular firearms accessories products are designed to increase weapon performance and accuracy. Due to it‘s outstanding materials construction, this rugged and high quality Austrian made item will serve you in any combat situation.NATO STANAG 4694 RailThe 10 slot Picatinny rail allows the user to upgrade his Modular Scope Mount equipped AUG rifle with additional accessories.SurfaceHigh alloy aluminium with anodized coating (MIL-8625-F type III, class II) for heavy use.This rails fits the AUG Modular Scope Mount (Art.Nr. 20114)

Claw Gear‘s modular firearms accessories products are designed to increase weapon performance and accuracy. Due to it‘s outstanding materials construction, this rugged and high quality Austrian made item will serve you in any situation.The SOF Compensator is a highly effective muzzle device designed to combine two Characteristics/Features. Reduce recoil and muzzle rise in a well-balanced mix.Breacher SpikesThese sharp and hardened steel spikes allow the user to destroy barriers in CQB situations.Mounting NotchesSix mounting grooves allow the compensator to fit on any AKSU based weapon system.Expansion ChamberThe construction guides the exhaust gases in optimal direction to reduce recoil and muzzle flip.Compatibility: AKS-74U, Krinkov AKSU and all variants based on these models with 24x1,5 muzzle threadInstallation: Dismount existing muzzle devices and clean the thread surface. After applying a drop of oil on the thread, screw the compensator counterclockwise on the barrel and push the locking pin on the front sight base completely flat. Screw the compensator tight and release the locking pin into the next mounting notch available. Before using a silencer make sure the compensator is not moving at all.

Clawgear‘s muzzle device products are designed to increase weapon performance and handling. Due to it‘s hardened steel construction, this rugged and high quality item will serve you in any combat situation.The Blast Forward Compensator is a linear type of compensator. Due to the design of the inside construction the muzzle blast is guided straight forward. This decreases the user’s exposure to noise, exhaust gases and powder particles as well the muzzle blast. Especially useful in confined spaces (CQB) and for those who are operating in a team. Also when standing alongside next to each other on the firing line or on the range, the Clawgear BFC is the ideal choice.Made from steel and treated with a black surface coating to make it even more durable. It is ideal for short barrel rifles, with no barrel length restrictions.3 Expansion ChambersThe construction guides the exhaust gases in optimal direction to reduce recoil and muzzle flip.Counter NutMount the AUG SOF Compensator with the counter nut to ensure a secure fit on the barrel.Breacher SpikesThese hardened steel spikes allow the user to destroy barriers in CQB situations. They can also be used as a fastening point with the included tool.Closed BodyForwards exhaust gases and noise away from the user.CompatibilitySteyr AUG A1/A2, AUG A3, AUG A3 SF, AUG P, AUG Z with thread, AUG Z A3 with thread, AUG LMG variants, AUG SA variants, F88 Austeyr, Thales EF88 / F90, MSAR STG-556InstallationMake sure your weapon is unloaded and safe. Dismount existing muzzle devices and clean the thread surface. After applying a drop of oil on the thread, screw the counter nut counterclockwise on the barrel until it stops. Screw the compensator counterclockwise on the barrel so it touches the counternut - then turn it back until the Claw Gear logo faces upwards. Tighten the counternut towards the compensator by hand and use a 19 mm wrench or the included tool to secure the position.

Clawgear’s nylon equipment is designed to increase the operator's performance. These products are optimized to be as versatile and lightweight as possible. The use of bonded Reinforced materials same time massively increases the durability and lifetime maintaining a low weight.The Front-End Kit Paracord is designed for Clawgear slings or other utilizing a similar 25mm plastic buckle mounting option. This front-end kit has a fixed military grade paracord loop for direct attachment.Features:Designed for Clawgear 2 -point Sling and Clawgear Sniper Rifle Sling or similar slingsMade of Nylon webbing in conjunction with military grade ParacordPlastic buckle attachmentFabrics:Nylon WebbingITW Nexus 30mm plastic loopType III 550 ParacordDimensions:Length: 24cmWidth: 3cm

Clawgear‘s muzzle device products are designed to increase weapon performance and handling. Due to it‘s hardened steel construction, this rugged and high quality item will serve you in any combat situation.The Blast Forward Compensator is a linear type of compensator. Due to the design of the inside construction, the muzzle blast is guided straight forward. This decreases the user’s exposure to noise, exhaust gases and powder particles as well the muzzle blast. Especially useful in confined spaces (CQB) and for those who are operating in a team. Also when standing alongside next to each other on the firing line or on the range, the Clawgear BFC is the ideal choice.Made from steel and treated with a black surface coating to make it even more durable. It is ideal for short barrel rifles, with no barrel length restrictions.3 Expansion ChambersThe construction guides the exhaust gases in optimal direction to reduce recoil and muzzle flip.Mounting NotchesTwelve mounting grooves allow the compensator to fit on any AK based weapon system.Breacher SpikesThese hardened steel spikes allow the user to destroy barriers in CQB situations.Closed BodyForwards exhaust gases and noise away from the user.CompatibilityAK-47, AKM, RPK, AK-74 and all variants based on these models with 14x1 LH muzzle thread. Does not fit on AK-100 Series, AKS-74U, Saiga riflesInstallationMake sure your weapon is unloaded and safe. Dismount existing muzzle devices and clean the thread surface. After applying a drop of oil on the thread, screw the compensator counterclockwise on the barrel and push the locking pin on the front sight base completely flat. Screw the compensator tight and release the locking pin into the next mounting notch available. Before using a silencer make sure the compensator is not moving at all.

Clawgear’s nylon equipment is designed to increase the operator's performance. These products are optimized to be as versatile and lightweight as possible. The use of bonded Reinforced materials same time massively increases the durability and lifetime maintaining a low weight.The Front-End Kit QD Swivel is designed for Clawgear slings or other utilizing a similar 25mm plastic buckle mounting option. This front-end kit has a fixed QD Swivel.Features:Designed for Clawgear 2 -point Sling and Clawgear Sniper Rifle Sling or similar slingsMade of 500D Nylon and bonded Laminate for extreme robustnessPlastic buckle attachmentFabrics:500D Nylon bonded with NBR fabricITW Nexus 25mm female buckleSteel QD SwivelDimensions:Length: 11cmWidth: 3cm

Clawgear’s nylon equipment is designed to increase the operator's performance. These products are optimized to be as versatile and lightweight as possible. The use of bonded Reinforced materials same time massively increases the durability and lifetime maintaining a low weight.The Front-End Kit Snap Hook is designed for Clawgear slings or other utilizing a similar 25mm plastic buckle mounting option. This front-end kit has a fixed Snap Hook.Features:Designed for Clawgear 2 -point Sling and Clawgear Sniper Rifle Sling or similar slingsMade of 500D Nylon and bonded Laminate for extreme robustnessSnap Hook covered with an elastic webbing collar to prevent weapon from scratchingPlastic buckle attachmentFabrics:500D Nylon bonded with NBR fabricITW Nexus 25mm female buckleSteel Snap HookDimensions:Length: 11cmWidth: 3cm

The Starblast compensator is the newest model of the CG Muzzle devices. It is a hybrid design of a muzzle brake and compensator.Outfitted with the Nato A2 standard interface to provide the option to mount any suppressor or blast deflector with the NATO QD mount(B&T Rotex V, Steyr UMS, or the Blast Deflector from B&T).Compatibility: All AR-15 and M16 variants in .223 or 5.56 mm caliber with a barrel thread of 1/2 x 28 TPI UNEF, for example: Hera Arms The 15th, Schmeisser AR15, DPMS AR-15,Steyr STM556 etc. Does not fit Oberland Arms OA-15

Clawgear’s nylon equipment is designed to increase the operator's performance. These products are optimized to be as versatile and lightweight as possible. The use of bonded Reinforced materials same time massively increases the durability and lifetime maintaining a low weight.The Front-End Kit Mash Hook is designed for Clawgear slings or other utilizing a similar 25mm plastic buckle mounting option. This front-end kit has a fix Mash Hook, covered with an elastic webbing collar to prevent weapon from scratching.Features:Designed for Clawgear 2 -point Sling and Clawgear Sniper Rifle Sling or similar slingsMade of 500D Nylon and bonded Laminate for extreme robustnessMash Hook covered with an elastic webbing collar to prevent weapon from scratchingPlastic buckle attachmentFabrics:500D Nylon bonded with NBR fabricITW Nexus 25mm female buckleStainless Steel Mash HookDimensions:Length: 11cmWidth: 3cm

Clawgear‘s muzzle device products are designed to increase weapon performance and handling. Due to it‘s hardened steel construction, this rugged and high quality item will serve you in any combat situation.The Blast Forward Compensator is a linear type of compensator. Due to the design of the inside construction the muzzle blast is guided straight forward. This decreases the user’s exposure to noise, exhaust gases and powder particles as well the muzzle blast. Especially useful in confined spaces (CQB) and for those who are operating in a team. Also when standing alongside next to each other on the firing line, or on the range the Clawgear BFC is the ideal choice.Made from steel and treated with a black surface coating to make it even more durable. It is ideal for short barrel rifles, with no barrel length restrictions.3 Expansion ChambersThe construction guides the exhaust gases in optimal direction to reduce recoil and muzzle flip.Crush WasherMount the AR-10 US Blast Forward Compensator with the crush washer to ensure the correct alignment on the barrel.Breacher SpikesThese hardened steel spikes allow the user to destroy barriers in CQB situations. They can also be used as a fastening point with the included tool.Closed BodyForwards exhaust gases and noise away from the user.CompatibilityAll AR-10 in .308 or 7.62x51 mm caliber with a barrel thread of 5/8 x 24 TPI UNEF, for example: DPMS LR .308, DPMS G2, DD-AR .308, Bushmaster AR-10, S&WM&P10, etc... Does not fit Oberland Arms OA-10InstallationMake sure your weapon is unloaded and safe. Dismount existing muzzle devices and clean the thread surface. After applying a drop of oil on the thread, put the crush washer over the thread (the conical end facing towards muzzle). Screw the compensator clockwise on the barrel by hand until it fits snugly. Then use a 19 mm wrench or the included tool to tighten the compensator until the Claw Gear logo faces upwards.

Clawgear‘s muzzle device products are designed to increase weapon performance and handling. Due to it‘s hardened steel construction, this rugged and high quality item will serve you in any combat situation.The Blast Forward Compensator is a linear type of compensator. Due to the design of the inside construction the muzzle blast is guided straight forward. This decreases the user’s exposure to noise, exhaust gases and powder particles as well the muzzle blast. Especially useful in confined spaces (CQB) and for those who are operating in a team. Also when standing alongside next to each other on the firing line, or on the range the Clawgear BFC is the ideal choice.Made from steel and treated with a black surface coating to make it even more durable. It is ideal for short barrel rifles, with no barrel length restrictions.3 Expansion ChambersThe construction guides the exhaust gases in optimal direction to reduce recoil and muzzle flip.Breacher SpikesThese hardened steel spikes allow the user to destroy barriers in CQB situations. They can also be used as a fastening point with the included tool.Closed BodyForwards exhaust gases and noise away from the user.CompatibilitySwissArms SG553 with threaded barrelInstallationMake sure your weapon is unloaded and safe. Dismount existing muzzle devices and clean the thread surface. After applying a drop of oil on the thread, put the crush washer over the thread (the conical end facing towards muzzle). Screw the compensator clockwise on the barrel by hand until it fits snugly. Then use a 19 mm wrench or the included tool to tighten the compensator until the Claw Gear logo faces upwards.Thread: M14x1 left

Clawgear’s nylon equipment is designed to increase the operator's performance. These products are optimized to be as versatile and lightweight as possible. The use of bonded Reinforced materials same time massively increases the durability and lifetime maintaining a low weight.The Rear End Kit Paracord is designed for Clawgear slings or other utilizing a 25mm webbing loop. This rear end kit has a military grade paracord loop for attaching to various sling swivels or loops.Features:Designed for Clawgear 2-point Sling and Clawgear Sniper Rifle Sling or similar slingsMade of Nylon webbing in conjunction with military grade ParacordFabrics:Nylon WebbingITW Nexus 30mm plastic loopType III 550 ParacordDimensions:Length: 24cmWidth: 3cm

Clawgear‘s muzzle device products are designed to increase weapon performance and handling. Due to it‘s hardened steel construction, this rugged and high quality item will serve you in any combat situation.The Blast Forward Compensator is a linear type of compensator. Due to the design of the inside construction the muzzle blast is guided straight forward. This decreases the user’s exposure to noise, exhaust gases and powder particles as well the muzzle blast. Especially useful in confined spaces (CQB) and for those who are operating in a team. Also when standing alongside next to each other on the firing line or on the range, the Clawgear BFC is the ideal choice.Made from steel and treated with a black surface coating to make it even more durable. It is ideal for short barrel rifles, with no barrel length restrictions.3 Expansion ChambersThe construction guides the exhaust gases in optimal direction to reduce recoil and muzzle flip.Crush WasherMount the OA-15 Blast Forward Compensator with the crush washer to ensure the correct alignment on the barrel.Breacher SpikesThese hardened steel spikes allow the user to destroy barriers in CQB situations. They can also be used as a fastening point with the included tool.Closed BodyForwards exhaust gases and noise away from the user.CompatibilityOberland Arms OA-15InstallationMake sure your weapon is unloaded and safe. Dismount existing muzzle devices and clean the thread surface. After applying a drop of oil on the thread, put the crush washer over the thread (the conical end facing towards muzzle). Screw the compensator clockwise on the barrel by hand until it fits snugly. Then use a 19 mm wrench or the included tool to tighten the compensator until the Claw Gear Logo faces upwards.

Clawgear’s nylon equipment is designed to increase the operator's performance. These products are optimized to be as versatile and lightweight as possible. The use of bonded Reinforced materials same time massively increases the durability and lifetime maintaining a low weight.The Rear End Kit Snap Hook is designed for Clawgear slings or other utilizing a 25mm webbing loop. This rear end kit has a steel snap hook for attaching to various sling swivels or loops. The Snap Hook is covered with an elastic webbing collar to prevent weapon from scratching.Features:Designed for Clawgear 2-point Sling and Clawgear Sniper Rifle Sling or similar slingsMade of bonded Laminate for extreme robustnessSnap Hook covered with an elastic webbing collar to prevent weapon from scratchingFabrics:500D Nylon bonded with NBR fabricITW Nexus 30mm plastic loopSteel Snap HookDimensions:Length: 11cmWidth: 3cm

Picatinny Rail for M-LOKFeature List:• Picatinny Rail for M-LOK interface with 9 slots.• Made from hight strength aluminium and a durablehard coat anodized finish, that meets Mil specrequirements.• Mounting hardware included (Nuts and Screws), withstainless steel T Nuts to avoid corrosion. Nocoating that can wear off or chip away when mountedand dismounted several times.Note:When mounting the Rail and tightening the screws, be sure not to overtighten them.The proper torque specs are max. 4Nm or 35in/lb.Tip: Use the short handle of the Allen key for tightening.*

Made of high strength aluminum with Mil-Spec Type III hard coat anodized finishFeatures a non-glare coating to reduce reflectionsMakes the A3 rifle compatible with the Clawgear AUG HandguardFeatures a 30 slot picatinny rail (NATO STANAG 4694)Anti-rotational QD attachment point at the front

Clawgear’s nylon equipment is designed to increase the operator's performance. These products are optimized to be as versatile and lightweight as possible. The use of bonded Reinforced materials same time massively increases the durability and lifetime maintaining a low weight.The Rear End Kit Mash Hook is designed for Clawgear slings or other utilizing a 25mm webbing loop. This rear end kit has a steel Mash Hook for attaching to various sling swivels or loops.Features:Designed for Clawgear 2 -point Sling and Clawgear Sniper Rifle Sling or similar slingsMade of bonded Laminate for extreme robustnessMash Hook covered with an elastic webbing collar to prevent weapon from scratchingFabrics:500D Nylon bonded with NBR fabricITW Nexus 30mm plastic loopSteel Mash HookDimensions:Length: 11cmWidth: 3cm

The Starblast compensator is the newest model of the CG Muzzle devices. It is a hybrid design of a muzzle brake and compensator.Outfitted with the Nato A2 standard interface to provide the option to mount any suppressor or blast deflector with the NATO QD mount(B&T Rotex V, Steyr UMS, or the Blast Deflector from B&T).Mounting grooves allow the compensator be timed on any AK based weapon system.Fits AK-47, AKM, RPK, AK-74 and all variants based on these models with 14x1 LH muzzle thread. Does not fit on AK-100 Series, AKS-74U, Saiga rifles.

Claw Gear‘s modular firearms accessories products are designed to increase weapon performance and accuracy. Due to it‘s outstanding materials construction, this rugged and high quality Austrian made item will serve you in any situation.Breacher SpikesThese sharp and hardened steel spikes allow the user to destroy barriers in CQB situations.Expansion ChamberThe construction guides the exhaust gases in optimal direction to reduce recoil and muzzle flip.Crush WasherMount the OA-15 SOF Compensator with the crush washer (enclosed) to ensure the correct alignment on the barrel.Closed BottomPrevents blown up dust and debris.Compatibility: Oberland Arms OA-15 modelsInstallation: Dismount existing muzzle devices and clean the thread surface. After applying a drop of oil on the thread, put the crush washer over the thread (the conical end facing towards muzzle). Screw the compensator clockwise on the barrel by hand until it fits snugly. Then use a 19 mm wrench to tighten the compensator until the Claw Gear logo faces upwards.

Claw Gear‘s modular firearms accessories products are designed to increase weapon performance and accuracy. Due to it‘s outstanding materials construction, this rugged and high quality Austrian made item will serve you in any situation.The SOF Compensator is a highly effective muzzle device designed to combine two Characteristics/Features. Reduce recoil and muzzle rise in a well-balanced mix.Breacher SpikesThese sharp and hardened steel spikes allow the user to destroy barriers in CQB situations.Expansion ChamberThe construction guides the exhaust gases in optimal direction to reduce recoil and muzzle flip.Crush WasherMount the G3/G36 SOF Compensator with the crush washer to ensure the correct alignment on the barrel.Closed BottomPrevents blown up dust and debris.Compatibility: H&K G36 and variants, H&K 416 and variants, OA-10, H&K G3 and variants with M15x1 muzzle threadInstallation: Dismount existing muzzle devices and clean the thread surface. After applying a drop of oil on the thread, put the crush washer over the thread (the conical end facing towards muzzle). Screw the compensator clockwise on the barrel by hand until it fits snugly. Then use a 19 mm wrench to tighten the compensator until the Claw Gear logo faces upwards.

Clawgear‘s muzzle device products are designed to increase weapon performance and handling. Due to it‘s hardened steel construction, this rugged and high quality item will serve you in any combat situation.The Blast Forward Compensator is a linear type of compensator. Due to the design of the inside construction the muzzle blast is guided straight forward. This decreases the user’s exposure to noise, exhaust gases and powder particles as well the muzzle blast. Especially useful in confined spaces (CQB) and for those who are operating in a team. Also when standing alongside next to each other on the firing line, or on the range the Clawgear BFC is the ideal choice.Made from steel and treated with a black surface coating to make it even more durable. It is ideal for short barrel rifles, with no barrel length restrictions.3 Expansion ChambersThe construction guides the exhaust gases in optimal direction to reduce recoil and muzzle flip.Counter NutMount the G3/G36 BF Compensator with the counter nut to ensure a secure fit on the barrel.Breacher SpikesThese hardened steel spikes allow the user to destroy barriers in CQB situations. They can also be used as a fastening point with the included tool.Closed BodyForwards exhaust gases and noise away from the user.CompatibilityH&K G36 and variants, H&K 416 and variants, OA-10, H&K G3 and variants with M15x1 muzzle threadInstallationMake sure your weapon is unloaded and safe. Dismount existing muzzle devices and clean the thread surface. After applying a drop of oil on the thread, put the crush washer over the thread (the conical end facing towards muzzle). Screw the compensator clockwise on the barrel by hand until it fits snugly. Then use a 19 mm wrench or the included tool to tighten the compensator until the Claw Gear logo faces upwards.

Picatinny Rail for M-LOKFeature List:• Picatinny Rail for M-LOK interface with 7 slots.• Made from hight strength aluminium and a durablehard coat anodized finish, that meets Mil specrequirements.• Mounting hardware included (Nuts and Screws), withstainless steel T Nuts to avoid corrosion. Nocoating that can wear off or chip away when mountedand dismounted several times.Note:When mounting the Rail and tightening the screws, be sure not to overtighten them.The proper torque specs are max. 4Nm or 35in/lb.Tip: Use the short handle of the Allen key for tightening.

Clawgear’s nylon equipment is designed to increase the operator's performance. These products are optimized to be as versatile and lightweight as possible. The use of bonded Reinforced materials same time massively increases the durability and lifetime maintaining a low weight.The Front-End Kit Loop is designed for Clawgear slings or other utilizing a similar 25mm plastic buckle mounting option. This front-end kit has an adjustable 25mm webbing loop for attaching various sling swivels or hooks.Features:Designed for Clawgear 2 -point Sling and Clawgear Sniper Rifle Sling or similar slingsMade of Nylon webbingMounting Loop size adjustablePlastic buckle attachmentFabrics:32mm Nylon WebbingITW Nexus 25mm female buckleDimensions:Length: 10cm+ (adjustable)Width: 3cm

• Matt black non-glare surface coating to reduce reflections• QD sling attachment point on the rear side of the handguard• M-LOK mounting system to fit all types of M-LOK accessories: rails, vertical grips, AFG, ...• Fits a wide variety of AK 47‘s with stamped and milled receivers with a front sling loop on the gasblock• Lightweight construction made out of high strength 6061 aluminium with MIL-SPEC type III hardcoat anodize finish

Clawgear‘s modular mounting system products are designed to increase weapon performance and handling. Due to it‘s construction in 6082 Aluminum, this rugged and high quality item will serve you in any combat situation.NATO STANAG 4694 RAILThe 13 slot Picatinny Rail allows the user to upgrade his 55X rifle with various aiming devices or accessories.LIGHTWEIGHT CONSTRUCTIONAlthough this mount base has been designed in a lightweight way, its mechanical strength is not being affected.ADJUSTMENT SCREWIt clamps the mount for a solid fit between both attachment points on the receiver and is secured by a clamp screw on the left side.DOVETAIL SLOTThe front attachment point is the dovetail on the receiver which is normally used to fix the brass catcher.CompatibilitySIG550, SIG551, SIG552, SIG553, PE90 and all variants of the rifle with standard adjustable diopter sights.InstallationMake sure your weapon is unloaded and safe. Screw the included adjustment screw fully into the mount base. Put the rail on the upper receiver and slide it forward so the dovetail on the receiver connects smoothly to the front of the rail. Then use a 8mm wrench to unscrew the adjustment screw until it moves inside the hole of the rear sight base. Tighten it up for a solid fit. Use the clamp screw on the left side of the mount base to secure its position.

• Matt black non-glare surface coating to reduce reflections• QD sling attachment point on the rear side of the handguard• M-LOK mounting system to fit all types of M-LOK accessories: rails, vertical grips, AFG, ...• Fits a wide variety of AK 47‘s with stamped and milled receivers• Lightweight construction made out of high strength 6061 aluminium with MIL-SPEC type III hardcoat anodize finish