Accessori

Mission Sensor II is a reliable timepiece for military and law enforcement operators providing a high level of functionality. Featuring high-density polycarbonate case, black-ops design without any reflective metal parts, digital compass, barometer, altimeter and many more. Black matrix display with backlight toggle provides best possible visibility under difficult conditions. The button tones for using the mode button can be turned off.Features:High-density polycarbonate caseHardened acryl glassTear-resistant rubber bracelet with black anodized buckleWater reistant 3 ATM / 30m1 x CR2032Functions:Digital compassAltimeter (-706m to +9164m, data will be stored for 34h)Barometer (0.1mbar, 300 to 1100mbar, data will be stored for 34h)Thermometer (0.1°C, -10° to +60°, °C or °F, data will be stored for 34h)Second time zoneAlarm functionStopwatch function (1/100 sec accuracy, 100 h)Countdown timer (1 sec, 100 h)Digital calendar12/24-hour calendarElectro-luminescent backlightMagnetic declination adjustableEnergy save mode (display deactivated)Low battery indication==__ABMESSUNGEN__==Height: 14.5mmDiameter: 46.4mmBracelet width: 22mm

Steel: AUS-8Weight knife: 140 gWeight sheath: 125 g

Microsac

Reliable timepiece for military and law enforcement operators providing a high level of functionality. The Dual Timer has been developped due to very frequent demands for a dial which provides analog as well as digital functions. Featuring high-density polycarbonate case, black-ops design without any reflective metal parts, digital compass, world timer, alarm mode, chronograph and many more. White hands and black matrix display with backlight toggle provide great visibility under difficult conditions. The button tones for using the mode button can be turned off.Features:High-density polycarbonate caseHardened acryl glassTear-resistant rubber bracelet with black anodized buckleWater reistant 3 ATM / 30m1 x CR2032Functions:Digital compassWorld TimerAlarm functionStopwatch function (1/100 sec accuracy, 100 h)Countdown timer (1 sec, 100 h)Digital calendar12/24-hour calendarElectro-luminescent backlightMagnetic declination adjustableEnergy save mode (display deactivated)Low battery indication==__ABMESSUNGEN__==Height: 15mmDiameter: 45mmBracelet width: 22mm

The 6" lightstick is a portable and cost-efficient source of light. Each lightstick is a pliable plastic tube filled with two non-toxic chemical solutions, one held separate in a floating ampule to prevent activation until required. To activate, simply bend the tube and shake. This breaks the ampule and mixes the chemicals. A bright light is released via chemi-luminescense, a chemical reaction converting energy to light without heat, flame, or sparks. No batteries or bulbs are required. These lightsticks are suitable for a wide range of applications in combat, training and outdoor activity.

Our most versatile piece of equipment, a must have accessory for every basic configuration. Attaching a cable switch on your front grip, fixing your light-sticks on your plate carrier, holding your tourniquet on the shoulder straps of your vest and many more.Mil Spec, made from highest grade natural rubber. Made in USADimensions: 1-1/4 x 3/8 x .062 inches each

Special Limited Edition

High performance Lithium battery, 3.0 Volt and 1400 mAhOptimized for high demands in flashlights and electronic devices

Microsac

Microfibre towel 40X80CM

Microsac

Our most versatile piece of equipment, a must have accessory for every basic configuration. Attaching a cable switch on your front grip, fixing your light-sticks on your plate carrier, holding your tourniquet on the shoulder straps of your vest and many more.Mil Spec, made from highest grade natural rubber. Made in USADimensions: 2 x 3/8 x .062 inches each

Clawgear’s nylon equipment is designed to increase the operator's performance. These products are optimized to be as versatile and lightweight as possible. The use of bonded Reinforced materials same time massively increases the durability and lifetime maintaining a low weight.The Multi-Purpose ID Holder is an ID card sleeve which can be attached to any Velcro surface or to an included neck-strap adapter.Features:Designed for ID cardsMade of bonded Laminate for extreme robustnessAdjustable neck strapDetachable ID card compartment with HOOK fastenerTwo flat card slots on the rear of the holderFabrics:500D Nylon bonded with NBR fabricWoojin plastic partsDimensions:Height: 13cmWidth: 8,5cmID card pocket window size:Height: 9cmWidth: 6,5cm

Microfibre towel 60X120CM